- Country of manufacturePoland
- Installation methodIn-floor
- Heat exchanger materialCopper
- Количество теплообменников1 шт.
- Мощность номинальная3.517 кВт
- Рабочее давление10.0 МПа
- Испытательное давление16
"POLVAX" - is a producer of high-quality heating devices – vnutripolny water convectors. Basic purpose of vnutripolny convectors – heating of rooms in which the classical water system of heating is used.
Installation of convectors, unlike standard radiators, allows to achieve uniform distribution of temperature in the warmed room and to leave from a problem of fogging and frosting of window space. Transfer of thermal energy happens by natural or compulsory (by means of the silent fan) convections.
The high thermolysis of the convector, in comparison with standard heating devices, occurs due to use of modern technologies and materials, and also at the expense of the built-in silent fan that allows to use in the presence of the cooling equipment this design for cooling of rooms. For removal of condensate – the drainage system is provided. Also perhaps combined use of convectors in total with other heating devices (for example - with classical batteries).
The growing demand for heating devices of the POLVAX company (Poland) is based on high quality of production and the used materials, and also on the lowest prices in comparison with the European and domestic analogs presented at the heating market of Ukraine. Are intended for heating of dry rooms where there is no opportunity to make a wide niche. It can be used as it is autonomous in rooms with the low need for heating, and to be combined with other heating devices. Devices are characterized by high heating capacity, thanks to tangential electric fans. Operation of devices is also provided in the mode of natural convection (with the switched-off electric fan). Differ from each other in specifics of an assembly niche.
height: 245 mm; 180 mm; width: 135 mm, 160 mm (narrowest model of the vnutripolny convector);
KV.135.245 length: 750-1500 mm (upon the demand of the customer production of the convector of non-standard length with a step of 250 mm is possible).
KV.160.180 length: 600-3000 mm (upon the demand of the customer production of the convector of non-standard length with a step of 250 mm is possible).
temperature of the heat carrier is 40-90 °C;
test pressure is 1,6 MPas;
working pressure is 1,0 MPas;
noise level is 26-30 dB.
The copper-aluminum heat exchanger with the built-in vozdukhootvodchik - 1 piece;
The tangential elekroventilyator of STANDART working from alternating current of 12 V-from 1 to 4 pieces (depending on device length);
Plaits electric – from 1 to 4 pieces (depending on number of fans);
Box (at choice: SILVER, BLACK) - 1 piece;
Shutoff valves (the crane sharovy G 3/4 full bore) - 2 pieces;
** An eyeliner (flexible hoses, the increased section through passage) - 2 pieces;
** Support adjusting - 4 pieces;
Arms under the heat exchanger - 2 pieces;
Tape noise-attenuating – 2 pieces;
Level assembly (depending on device length) – 1-3 pieces;
Lattice decorative (wooden or dural) - 1 piece;
Covers protective - from 2 to 10 pieces (depending on a look and number of fans);
Level dividing - from 1 to 4 pieces (depending on device length);
The instruction - 1 piece;
Protective packing (box) - 1 piece;
Guarantee (in the instruction).
Ways of regulation of heating capacity of the device in devices with compulsory convection.
At turning on of the fan heating capacity of the convector increases up to 200%.
The programmable thermostat installed in a control point of the room operates operation of the fan.
* production of devices of the non-standard sizes is possible.
** at the request of the customer the complete set providing MANUAL regulation with heating capacity of devices is possible.
*** for the KV.160.180 version.