Currency EUR
Priming enamel POLYCOAT HS 17443 – Lakokraska, OAO | all.biz
Buy Priming enamel POLYCOAT HS 17443
Priming enamel POLYCOAT HS 17443

Priming enamel POLYCOAT HS 17443

Products from producer
In stock
Reconfirm the price with seller
Payment:
Shipping:
Seller
Belarus, Lida
(View map)
+375 
Display phones

Company rating

100% of positive reviews from 5
11
11 years on Allbiz
Technical characteristics
  • BrandLida
  • Country of manufactureBelarus
  • Type of useUniversal
  • Type of primerCorrosion
  • Base primerPolyurethane
  • Processed materialMetal
  • ColorIn assortment
  • Colorless materialNo
  • PurposeBuilding
Description

High - quality two - component polyurethane priming enamel high solids polyester reinforced with excellent corrosion resistance. Recommended as a topcoat in epoxy / polyurethane paint systems where high demands are set to preserve the color and mechanical strength. Primarily it recommended for use in petrochemical plants, oil drilling platforms, refineries, for dyeing tanks and metal in various industrial and atmospheric exposure conditions (up to C5). As a single layer coating may be applied under conditions corrosiveness medium C2.

ADVANTAGES

  • very high UV resistance
  • excellent adhesion;
  • excellent weather resistance
  • excellent corrosion resistance;
  • excellent flexibility;
  • NORSOK approved as a topcoat, reinforced polyester;
  • It can be applied directly to the metal substrate in selected under various conditions;
  • anti - graffiti properties can be obtained by using a special activator;
  • Sertificated in accordance with the COT KO 47.10.

THE WORKING PROCESS

Mixing: 17443 base component POLYCOAT HS - 8 parts by volume of

Activator 912 - 1 part by volume

Mixing instructions:

Vigorously mix the base component and an activator, preferably using a mechanical stirrer. mixed product temperature should be at least 10 ° C when used.

Dilution: Priming enamel can be applied to a variety of spray equipment. The required number PU5801 diluent depends on the equipment used, the method of application and temperature of the final product.

Life - ability: 2 hours at 20 ° C (mixed product).

Application conditions: substrate temperature should be above the dew point by at least 3 ° C. The surface must be well ventilated during application and drying to reduce solvent evaporation. This is to ensure good drying conditions and the health of malaria.

Method of application: Preferably equipment for combined spraying and airless. Brushing may result in uneven thickness and poor dispensing paint.

CHARACTERISTICS AND PROPERTIES

Decorative properties:

Gloss: Semigloss

Color: Standard color (eg RAL, NCS), also available version without chromate and lead.

Product Features:

Solids by volume: ± 68 vol. % (Mixed product)

LOC: ≤ 280 g / l.

Density: at 20 ° C ± 1,4 kg / l (mixed product)

Dry film thickness: Standard: 60 - 120 microns (depending on the method of application)

Theoretical coverage area: When a dry film thickness of 80 microns - 8.5 m2 / l.

Practical coverage area: The performance of the practice depends on various circumstances.

Airless spray:

large dimensions: 70% of the theoretical coverage area.

small size: 50% of theoretical coverage area.

Heat resistance: Maximum 120 ° C (dry heat)

Coverage: In order to achieve good hiding final coating of some colors require a special primer shade. Please contact the technical department for advice.

Drying time at standard dry film thickness of 80 microns (method: BYK - drying recorder) 5 ° C 10 ° C 20 ° C 30 ° C

Dust: 8 h 3 h 5 h 1 h

Touch dry: 48 hours 24 hours 18 hours 8 hours

Overlap: 40 h 24 h 12 h 8 h

Maximum recoat interval is unlimited, provided that the surface is clean and free from oil and grease. It should be taken into account that the films have a longer drying times thicker During drying and curing the relative humidity must be below 80% . Therefore, during this period should avoid any contact with moisture.

Rational solutions in the field of coatings

Technical data

CONDITIONS OF APPLICATION

airless Combined

Thinner: PU5801 PU5801

Quantity: 0 - 10% by volume 0 - 10% by volume

Nozzle: 0,015 - 0,017 0,015 - 0,017 inch inch

Pressure: 140 - 200 bar to 70 - 100 bar

Dry film thickness: 60 - 120 microns 60 - 120 microns

Roller / brush Pneumatic

Thinner: S5102 PU5801

Quantity: 0 - 5% by volume 5 - 10% by volume

Nozzle: 2.0 - 2.5 mm

Pressure: 3 - 4 bar

Dry film thickness: 60 microns 60 - 120 microns

Cleaning tools: immediately after application using PU5801 diluent.

PRODUCT INFORMATION:

Packing: 20 L jar. Thinner in 25 liter and 200 liter canisters barrels.

Warranty: In tightly closed original packaging is 12 months when stored indoors at temperatures from 5 ° C to 40 ° C.

TEST RESULTS

The accelerated environmental tests: ISO 11507 / ASTM G154 Gloss retention at 60 ° 3600 hours> 50%

coating tests on the effect of weathering: ISO 2810 5 years

Resistance to salt spray: NORSOK M501

Separation (before / after salt spray): ISO 4624 / ASTM D4541 4200 hours Norsok system 16743/17443 15.4 / 13.1 MPa

Elasticity: ISO 1519 / ASTM D522 cylindrical spindle 3 mm

Corrosion resistance: electrochemical impedance spectroscopy (EIS) Rc 3,7 * 109 (21 day) 4P system 16515/16743/17443

Immersion: ISO 2812 - 2 / ASTM D543X 1 7 days distilled. 7 days water H2SO4 (2% ) 7 days 7 days trietilglikol leafminer. oils

Compliance COT KO 16.76 Certified

ENVIRONMENT AND HEALTH

Labeling: In accordance with EU Directive 67/548 / EEG and in accordance with the directive on hazardous materials. Harmful and irritating in contact with skin, eyes and inhalation. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Do not eat, drink or smoke during application of the paint.

UN: 1263

Aware Code: 27 - IV

The AWARE - reduction Adequate Warning and Air Requirement (required warning and requirements for air quality) - a code system for products containing volatile organic compounds (VOCs), a tool for producers, which facilitates risk assessment and improvement of products. In addition, this system can be used to inform the final consumers about possible health risks. The system is based on the concept of the Norwegian regulatory requirements of fresh air at the workplace (OAR) and the Danish concept of MAL code system. AWARE code consists of two numbers separated by a hyphen. Both figures are based on the physical and chemical factors, and adapted to the European directive on hazardous part of the first figure expresses the number of the required fresh air in the workplace (in m3) to dissolve the evaporation of one liter of product used to make sure that does not exceed the maximum permissible concentration in the workplace (OEL). It is based on the content of the component vapor pressure, solubility and toxicity. The second figure is derived from the R - phrases that apply to substances in the product. That is AWARE is a tool that can be used to determine the risks of products and product components. The greater the value of AWARE, the higher the level of risk. This is an excellent tool to support the replacement of hazardous products. which refer to substances in the product. That is AWARE is a tool that can be used to determine the risks of products and product components. The greater the value of AWARE, the higher the level of risk. This is an excellent tool to support the replacement of hazardous products. which refer to substances in the product. That is AWARE is a tool that can be used to determine the risks of products and product components. The greater the value of AWARE, the higher the level of risk. This is an excellent tool to support the replacement of hazardous products.

PRELIMINARY PROCESSING

Untreated steel:

It is necessary that the surface be pre - treated according to ISO12944 part 4, §6.2.3. Remove grease, oil, dirt, etc. , using an appropriate scavenger, e. g. , ENVICLEAN PR (see for use. Product data sheet) and the spray gun operating under high pressure. Sandblasting to a purity of Sa 2½ in accordance with ISO 8501 - 1. After sandblasting to remove dust from the surface by means of compressed air, which does not contain particles of moisture and fat. Apply the first coating layer for 6 hours. If the final layer is applied to the construction site, special precautions should be taken.

Hot dip galvanized:

The surface must be pre - cleaned according to ISO12944 part 4 § 6.2.3.4.1 (inert abrasive grain cleaning). See. Also NEN 5254 for duplex systems. Remove grease, oil, dirt, etc. , using an appropriate scavenger, e. g. , ENVICLEAN PR (see for use. Product data sheet). Make delicate sandblast across the surface of the zinc with an inert agent (grain size 0.3 - 0.5 mm, pressure of 2.0 - 2.5 bar, the nozzle orifice: 6 mm min. ). After sandblasting the surface should be flat and smooth. Depending on the zinc layer according NEN5254, can be removed by zinc maximum 5 - 10μm. After sandblasting, remove all the dust from the surface by means of compressed air, wherein the particles have a moisture and fat. Apply the first coat for 2 hours.

WARRANTY AND DISCLAIMER

This sheet product data replaces all previously published. Data specification, guidance and recommendations in this sheet are the result of tests and experience under controlled or specially defined conditions. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and / or User. Products are supplied and all technical assistance is in accordance with our general terms of sale and delivery for paints and varnishes, printing inks and other products, unless otherwise agreed in writing. The Manufacturer and Seller disclaim, and Buyer and / or User waive all claims, including any kind of responsibility for the situation, arising out of negligence or for any other similar reason, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of products in accordance with the recommendations set out above, the reverse side of the sheet or other source. These products can be changed without notice. 17443 POLYCOAT HS

PROTECTIVE COATINGS

Our "protective coating" different strength, flexibility, adhesion, ease of application, anticorrosive properties, chemical and mechanical resistance. These high performance is achieved thanks to the extensive experience in the field of coating chemistries, as well as due to the attention to the needs and requirements of the client. Coating systems according to ISO 12944 and follow international guidelines on the contents of LOC.

PAINT SYSTEM

Below are some examples of coloring systems based on the use of 17443 PolyCoat HS. For specialized consultation system for coloring contact Baril Coatings, or to our local dealer.

System 1 Class corrosiveness medium C2

Single - layer system of 80 microns; 17443 PolyCoat HS

System 2 Class corrosiveness environment C3

1 - layer of 80 microns; 16442 UniBar ZFC

2 - ply 60 micron; 17443 PolyCoat HS

System 3 Class corrosiveness medium C5

1st layer 80 microns; 16442 UniBar ZFC

2nd layer 100 . mu. m; 16743 UniBar SteelKote® Miox

3rd layer 80 microns; 17443 PolyCoat HS

System 4 certified in accordance with Norsok M501

1st layer 150 . mu. m; 16743 UniBar SteelKote® Miox

2nd layer 150 . mu. m; 16743 UniBar SteelKote® Miox

3rd layer 100 . mu. m; 17443 PolyCoat HS

MINOR REPAIRS

Minor repairs of damage or rough parts of the construction site.

Remove grease, oil, dirt, etc. , using an appropriate scavenger, e. g. , ENVICLEAN PR (see for use. Product data sheet). Remove rust from mechanical damage, derived from accidents with transport or during assembly, untreated welds and scorched portions by means of rotating steel wire brushes, grinding disc or steel wire brushes and sanding with large grains to the extent St3 purification according to ISO 8501 - 1. Smooth transition from the stripped parts intact areas using grinding and cleaning. After grinding to remove dust from the surface by means of compressed air, wherein the particles have a moisture and fat. Then make a repair facility using full color system as described in the manual for staining.

SERVICE

It is recommended to regularly clean the surface and annually inspect the paintwork for defects.

TECHNICAL ASSISTANCE

Baril Coatings BV not only offers advice on the use of its products. We offer a full range of services for the superintendent, architect, general contractor and contractor for painting works. To provide the desired characteristics in terms of durability, Baril Coatings offers full technical support and supervision during implementation and completion of the application process time according to ISO 12944. The supervision and support provided by Baril Coatigs, do not relieve the contractor of painting works from the responsibility for its tasks. The contractor for painting works should be thoroughly familiar with those products, technical passports are often updated, and the general conditions of Baril Coatings for protective coatings applied to steel. Baril Coatings is not responsible for the application or application conditions.

WARRANTY AND DISCLAIMER

This sheet product data replaces all previously published. Data specification, guidance and recommendations in this sheet are the result of tests and experience under controlled or specially defined conditions. Their accuracy, completeness or appropriateness under the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and / or User. Products are supplied and all technical assistance is in accordance with our general terms of sale and delivery for paints and varnishes, printing inks and other products, unless otherwise agreed in writing. The Manufacturer and Seller disclaim, and Buyer and / or User waive all claims, including any kind of responsibility for the situation, arising out of negligence or for any other similar reason, except as expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of products in accordance with the recommendations set out above, the reverse side of the sheet or other source. These products can be changed without notice

Comments about the company  Lakokraska, OAO
100%
of positive feedback from the 5
100% of responses during the day
100% of transactions executed in time
100% of actual goods description
This means that 100% of buyers found cooperation with this company successful and recommend this seller
all (5) positive (5) negative (0)
Good
раимбеков жанат чалбаевич
раимбеков жанат чалбаевич
22.05.2019
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
пока идут переговоры Надеемся на успех
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Good
Игорь
Игорь
08.03.2019
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
Отлично. Оперативно. Тактично.
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Good
Anonymous
26.03.2018
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
Prompt response: Within one hour
Was the order is executed in time: I can not appreciate
Corresponding of goods/services description: I can not appreciate
Good
Дмитрий
Дмитрий
22.09.2017
Allbizconfirms appeals
Allbiz confirms a receiver's contacting via resource
супер пупер молодцы !
Prompt response: Within one hour
Was the order is executed in time: Yes
Corresponding of goods/services description: Yes
Contact the seller
Priming enamel POLYCOAT HS 17443
Priming enamel POLYCOAT HS 17443
Shipping method
Payment method
Compare0
ClearSelected items: 0