- BrandFRESKO
- Country of manufactureBelarus
- Type of useFor interior applications
- Processed materialPlaster
- ColorIn assortment
- Colorless materialNo
- PurposeBuilding
It is intended for priming the walls and ceilings before applying water - dispersion paints for indoor and outdoor use on concrete, brick, plaster, putty, drywall, and before pasting wallpaper. Perhaps the use of a primer for dust removal of concrete bases (eg, floor before laying linoleum, parquet).
| number | indicator | requirements ROV |
| «FRESKO Bind» | ||
| one | Appearance primer | Unclear - white liquid |
| 2 | Mass fraction of solids, % | 4.5 |
| 3 | Hydrogen ion concentration, pH | 7.0 - 9.0 |
| 4 | Drying time to degree 3 at (20,0 ± 2) ° C, h, max | one |
Advantages: primer does not require thinning, easy to apply, dries quickly, does not have a particular smell. Good levels and reduces the absorbency of various bases, which provides uniform application of subsequent layers of paint and its adhesion to the base. This reduces ink consumption.
Surface preparation: Before applying the primer with facades mechanically removed moss, tar spots. Surfaces having efflorescence necessary clean dry method (brushing). In operation the surfaces of this type can not ensure the durability of the coating, because of possible repeated appearance of salt deposits and, in consequence, the violation coating adhesion to the substrate.
The surface must be clean, dry, solid, exhibit good load bearing capacity and does not contain substances which reduce adhesion (release agents).
Fresh mineral surfaces (plaster, putty) before priming concrete should be conditioned for at least 28 days at a temperature not below 10 ° C, the allowable residual moisture bases - not more than 8% .
The old surface, previously painted with mineral paints, loosely hold the coating, peeling of the base, chalk or lime, chalk coating was removed completely washing apparatus under high pressure or by mechanical means. After wet cleaning is necessary to give the ground to dry well. Peeled surface and coating defects are aligned plaster solution or polymeric fillers, sanded and cleaned of abrasive residues. Glossy concrete surface is treated mechanically to give them a surface roughness (surface should be matte).
Panelists metal parts (valves, caps and nails etc. ) cleaned of rust and paint primer "Akvapraym" (TU BY 500021625.125) or primer "LidAkril" (TU BY 500021625.124), or primer enamel "Ekolyuks" (TU BY 500021625.145 ).
Coating: primer before applying the mix thoroughly. The primer is applied in undiluted form a uniform layer with a brush, brush or roller in one or two coats (depending on the absorbency of the surface) at ambient temperature and the surface from plus 7 ° C to plus 35 ° C, under favorable weather conditions, ie . e. in the absence of rain, strong wind or fog. After the rain hold staining should only after 2 - 3 days exposure surface at a temperature not lower than 15 ° C. Deviation from these recommendations may occur deterioration of performance and processability priming.
Drying Time primer no more than 1 hour at ambient temperature (20 ± 2) ° C and a relative humidity of 65% .
To perform the subsequent work can begin no sooner than 2 hours after priming. Properly primed surface should be matte, and in any case should not shine
Drying Time primer no more than 1 hour at ambient temperature (20 ± 2) ° C and a relative humidity of 65% .
To perform the subsequent work can begin no sooner than 2 hours after priming. Properly primed surface should be matte, and in any case should not shine
Consumption of 100 - 125 g / m2 excluding roughness, porosity, absorbency of the substrate, the application method, etc. painter qualification factors. . When priming textured and highly absorbent surfaces primer flow can reach 200 g / m2.
Not be mixed with other primer paints and solvents of any type.
Tool wash water container and not later than 10 - 15 minutes after application.
After using the primers as intended container with product residues to be tightly closed closures and sent to the consumer landfill.
Storage: The primer must be stored in a sealed polyethylene containers and transported at a temperature from + 5 ° C to plus 35 ° C. Do not expose to high temperatures and direct sunlight. In winter, the primer is transported in insulated truck and stored in heated storage rooms.
Precautions: In accordance with the GOST 12.1.044 primer refers to the group T1 Harmful chemicals, to the group with high smoke - forming capability D3 according to GOST 30244 - to the group G1 flammability. Primer fire and explosion. The primer is a substance of low hazard (4 class of hazard according to GOST 12.1.007). The dried coating has no adverse impact on the environment and the human body.
Persons related to the paint work must be provided with personal protective equipment (overalls, safety glasses, rubber gloves). Accidental contact with the eyes, mucous membranes and the skin rinsed with water.
