Kromkooblitsovochny Filato FL-230 machine

Kromkooblitsovochny Filato FL-230 machine
Edge thickness: 0,4-3 mm, panel Thickness: 10-60 mm, giving Speed: 6-20 m/min.

Appointment

It is intended for a veneering of rectilinear edges of slabby materials by rolled edges of ABS, PVH and strip edging material up to 3 thick (10) mm.

Distinctive features

• Speed of giving of 6 - 20 m/min, is regulated stepless
• Tank for glue fusion with the electronic block of control of temperature -
• The teflon tank for glue under a kleenanosyashchy roller -
• Adjustment of amount of the applied glue -
• Guillotine for preliminary cutting of thick edging material from PVC or ABS-
• Tortsovochny knot for cutting of forward and back sves a saw with two engines of 12000 rpm. -
• Milling knot for removal of sves with vertical and horizontal control, with two high-frequency engines of 12000 rpm. Radius of a mill of 2 mm -
• Transport system with a chain. The bearing plates width – 80 mm -
• Clamping rollers of the top beam are made of rubber, are established on bearings -
• The hopper of the rolled edging material D800 of mm -
• The control panel on the forward panel of the machine -
• The supporting support for dimensional preparations -
• The regulator of compressed air, dehumidifier -

 -

The scheme of processing -

 -

 - - - - - - - - - - - - - Tortsovka - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Milling of sves

 -  -  -  -  -  -  -  -

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - Blocking a podachiblokirovka allows to give preparations at minimum safe distance from each other. • - the System automatically works, protecting from damage units, excepting influences "-a human factor"-. • - Distance between details of 400 mm. From giving speed the distance between details does not change.

 -

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - - the Knot preliminary obrezkisostoit from two uzlov1 (Type of scissors) Knot of preliminary cutting (type of scissors) for a thin edge (0.4-1 mm) • - Allows to cut off precisely without zalom an edge and a natural interline interval. • - Ideal option for a thin edge of PVC since the driving roller pulls for itself a thin edge. The edge in this case does not fly from a detail and is not rumpled.

 -

 -

2 (Type a knife) Knot of preliminary cutting (type a knife) for a thick edge (2-3 mm). • - It is equipped with a powerful pneumatic cylinder. Steadily cuts off a thick edge of any type.

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - - the Press of a gruppazon of a clip consists of three rollers. The first roller of big diameter driving, second and third repressing - conical. Distinctive features: • - Allows to press piece material up to 10 mm thick. • - Fast polymerization of glue at the expense of the big area of contact of the first roller (F 120 mm). • - Conical multidirectional rollers provide an ideal type of glue connection. • - Control for thickness of an edge happens to the help of the counter. Pneumatic adjustment of effort of a clip of rollers allows to pick up and check necessary value for an edge clip.

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - The knot face an obrezkidva industrial the engine (12000 rpm) of 2x1,1 kW TEKNOMOTOR (Italy) • - Is available a possibility of turn of saws 0-15 hail. • - Saws move on two a prismatic guide, each saw cuts off an allowance only on the one hand. This system proved as reliable and stable during all term of operation.

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - - Distinctive features: • - the simple linear movement of two saws up-down - • - Two prismatic guides which are 5 times stabler, than round guides. • - Wires of engines are protected by cable layers. It protects them from a mastication and damages. • - the Zone of a tortsovka is fenced off by a partition. Hit of scraps of an edge in glue knot and knot of a clip is excluded.

 -

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - - Milling an uzeldva industrial the engine (12000 rpm) of 2х0,11 kW TEKNOMOTOR (Italy). • - Power of engines of 1,1 kW allows to mill an edge with an allowance for the party more than 2 mm. • - Are equipped with counters of exact control for the different thickness of an edge. • - Mills whole 4 knives of F75-Z = 4-R2 LEUCO (Germany). • - Fast "-a spirit on an edge" - by installation of a sample of an edge of 0,4 mm or 2 mm under a copy rack. Does not demand additional fine tuning. • - there is a tilt angle of milling cutters 0-45 hail. Effective use of the cutting tool.

 -

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - - Copiers round big diameter: • - Carry out smooth calling on a detail. • - Exclude damage any revetted a surface. • - Provide exact copying of a surface of a detail.

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - Nastroykaregulirovka of all knots working at pneumatics is in one place that considerably simplifies adjustment of the machine.

 -

 -

 - - - - - - - - - - - - - - - - - - - - - - - - - Giving konveyerdetal moves the chain conveyor with the rubberized boots. Width of boots is 80 mm. This type of giving fixes more reliably and moves a detail along the machine. The drive - the motor reducer. Speed of movement of preparation changes smoothly from 6 - 20 m/min. It allows to pick up the optimum modes of processing necessary for the customer. The detail nestles on the conveyor a clamping beam with the two-row rollers established in chessboard order that it is the most rigid to record a detail on the conveyor.

 -

Technical characteristics
Thickness of edging material	mm	0,4 - 3
Thickness of a detail, min./max.	mm	10 - 60
The sizes of the processed detail (min.) - also width is long	mm	120 x 60
Giving speed	m/min	6 - 20
Power of engines tortsovki-2 pieces.	kW	2х0,37
Turns of saws	rpm	12000
Mills of knot of removal of sves of an edge on the plane - 2 pieces.	mm	F75-Z = 4-R2
Power of engines-2sht.	kW	2х1,1
Turns	rpm	12000
Branch pipes of system of aspiration	mm	1 x F 100
General power	kW	5,24
The feeding tension (3 phases)	In	380
Pressure of compressed air	Bar	6,5
Overall dimensions length width height	mm	2965 850 1380
Weight	kg	960

 -

 - -

Technical characteristics
Thickness of edging material	mm	0,4 - 3
Thickness of a detail, min./max.	mm	10 - 60
The sizes of the processed detail (min.) - also width is long	mm	120 x 60
Giving speed	m/min	6 - 20
Power of engines tortsovki-2 pieces.	kW	2х0,37
Turns of saws	rpm	12000
Mills of knot of removal of sves of an edge on the plane - 2 pieces.	mm	F75-Z = 4-R2
Power of engines-2sht.	kW	2х1,1
Turns	rpm	12000
Branch pipes of system of aspiration	mm	1 x F 100
General power	kW	5,24
The feeding tension (3 phases)	In	380
Pressure of compressed air	Bar	6,5
Overall dimensions length width height	mm	2965 850 1380
Weight	kg	960

 -

Accessories

The completing components of the leading global manufacturers:

TECNOMOTOR engines (Italy) -

The electronic Schneider components (Germany) -

The Leuco tool (Germany) -

FAG bearings (Germany) -

The frequency Delta converters (Taiwan) -

Guides of HIWIN (Taiwan).  -  -